James main logo black


Bi-Amped System For Large/Extra Large Area

Technology header click

Our top of the line landscape system is formulated to provide maximum coverage within a large area, while also providing each of those areas with uncompromising audio performance combined with minimal visual impact. By having the system bi-amped and incorporating the DSP processor allows you flexibility never before experienced in an outdoor audio system. We carefully measure and program each of these systems before they ever leave our facility, taking the guesswork out of your installation. The 159AT70 features the following items; (8) 62AT70 satellite speakers, (1) 151ST70 subwoofer, (1) M1000 amplifier, and (1)  CDi 2600 amplifier.

Our new 62AT70 landscape speakers now feature a coaxially mounted 1" aluminum dome tweeter design over a proprietary high-excursion 6" woofer, with a built-in crossover network and 100W/70V transformers. These outdoor speakers play at significantly higher volumes while still maintaining a smooth frequency response of 70-20kHz.  The 62AT70 speakers are powered by a  CDi 2600 amplifier providing 600W@70V per channel and features built in DSP for crossovers and equalization if required.

The 151ST70 landscape subwoofer was designed by James to provide broader coverage for systems that needed extra SPL. It features a proprietary high excursion 15" aluminum driver mounted within a fully sealed aluminum band-pass enclosure. Engineered for direct burial placement, the compression design creates unrivaled low end frequency response and nearly complete invisibility. You can install up to (4) of these subwoofers on a single run of 14/4 speaker wire when paired with our M1000 DSP amplifier.

Frequency Response

20Hz-20kHz +/-3dB

Nominal Impedance

70 volt Transformer


91dB 2.83V/1m


70 volts


Aircraft Marine Grade Aluminum


Sats - Black Wrinkle, Bronze Wrinkle, Verde, Weathered Iron, Premium Finishes and Plating Available

Product Documents

Related Documents

Click photo for download image options


159AT70 - Available downloads

Title: 159AT70 Lanscape System

Size Resolution (Right-click: Save link as...)
38.37 KB 900x900 159AT70.jpg

159AT70 - Available downloads

Title: 151ST70 subwoofer

Size Resolution (Right-click: Save link as...)
93.96 KB 900x900 151ST.jpg

159AT70 - Available downloads

Title: 62AT70 side

Size Resolution (Right-click: Save link as...)
84.99 KB 900x900 62AT.jpg
M1000 cropped %281%29

159AT70 - Available downloads

Title: M1000 component

M1000 cropped %281%29
Size Resolution (Right-click: Save link as...)
1.04 MB 900x900 M1000_cropped_(1).png
Cdi2600 front web

159AT70 - Available downloads

Title: CDi2600 AMP Front

Cdi2600 front web
Size Resolution (Right-click: Save link as...)
18.65 KB 900x900 CDi2600_Front_Web.jpg
159at pool side

159AT70 - Available downloads

Title: 159AT Poolside

159at pool side
Size Resolution (Right-click: Save link as...)
436.61 KB 1350x900 159AT-Pool-Side.jpg
At system

159AT70 - Available downloads

Title: AT Installation

At system
Size Resolution (Right-click: Save link as...)
88.39 KB 675x900 AT-System.jpg

James Loudspeaker Helps Expand Maverick Integration's Outdoor Audio Business

Dennis Jaques of Maverick Integration in Nashua, N.H., explains how the 70V Landscape Series line of speakers from James Loudspeaker enabled the company to expand its outdoor audio business.


Sound Waves Discusses Why They Love James Loudspeaker's Outdoor Tech

Joe DeMarco says he was so impressed by James' outdoor technology that he went out to visit the company to learn more.

Category FAQs

Traditional 70V speakers will have a transformer as the load.  Because tranformers react differently to DC and AC signals, an ohm meter reading will measure the DC resistance (DCR) of the transformer and will not provide any info on the actual rating of the speaker when passing audio, and might even read near 4 or 8 ohms which might indicate incorrectly, it is a 4 or 8 ohm speaker.  In the audio band, the impedance presented by the transformer will be much greater than the DC resistance.

Unlike traditional 70V speakers, James Landscape sats, the AT series, also feature an additional low frequency roll off via a built-in network to protect the speaker as well as allow running the sats on the same line as a subwoofer.  These features block all DC signals, making an ohm-meter useless for testing as it will measure "open circuit" on both 4 ohm and 70V speakers.

So the speaker must be measured with an 70V IMPEDANCE METER which characterises the IMPEDANCE at 1kHz, not at DC RESISTANCE.  Examples follow the table.

Below is a table which shows impedance and DCR reading to be expected on AT sats and ST subwoofers.

Table1 - AT and ST loudspeaker impedance data
32AT4 9 ohms open  
32AT70 300 ohms open  
42AT4 7 ohms open  
42AT70 150 ohms open  
62AT4 11 ohms open  
62AT70 105 ohms open  
81ST4     Bi-amp only
81ST70     Bi-amp only
81ST70-X     Crossover for fullrange systems
101ST4     Bi-amp only
101ST70     Bi-amp only
101ST70-X     Crossover for fullrange systems
121ST4     Bi-amp only
121ST70     Bi-amp only
121ST70-X     Crossover for fullrange systems
151ST4     Bi-amp only

Bi-amp only

Fig 1 shows three examples of 70V impedance measurement tools; the TOA  ZM-104A, the TENMA 72-6948, and the Dayton Audio DATS2 speaker testing software.  The two impedance meters test at only 1kHz which can give you readings which may appear out of spec, where as DATS2 gives you a full 20Hz to 20kHz impedance curve so you see all the data and read the frequency of interest.  DATS2 is our favorite as it works with a laptop, is small and also the cheapest of the options.

Fig 1 - 70V mesurement tools

To show the versatility of DATS2, Fig 2 below shows a DATS2 curve run on a 32AT70 loudspeaker.  To get the same reading as an impedance meter, you would read the impedance at 1kHz o the graph, but as you can see, there is a wealth of information in the curve.  In this example, DATS2 is calling out about 281 ohms at 1 kHz, close to the 300 the impedance meters will read.

For those with an understanding of the math, the power at 1kHz will be 5000/281 = 18W.  The lowest impedance is around 450 Hz at about 190 ohms, giving 5000/190 = 26W.  So as you can see, even though the transformer is rated at 30W at 4 ohms, when used with a speaker the real power is quite different. 

When this same transformer is loaded with a 4 ohm resisitive load, the reading is 140 ohms which is 5000/140 =3 5W, typical for a 30W rating.  So all contant voltage transformers, regardless if they are 25V, 70V or 100V, only have a nomial power rating at a nominal load impedance - results will vary in use!


Fig 2 - DATS2 curve of 32AT70

Welcome! Admin Login
Ph: +1.775.461.7500 | Fx: +1.775.461.7599
Ā© Copyright 2019 James Loudspeaker LLC