James main logo black

ST15-70

15" Subterranean Subwoofer (70V)

Technology header click
Tags:

The ST15-70 features a proprietary high excursion 15" aluminum driver mounted within an aluminum sealed band-pass enclosure. Engineered for direct burial placement, the compression design creates unrivaled low end frequency response, and nearly complete invisibility. You can install up to (4) of these subwoofers on a single run of 14/4 speaker wire when paired with our M1000 DSP amplifier! The external hooded port, aircraft/marine grade aluminum enclosure and stainless steel hardware provide for increased protection in extreme weather conditions. This unit is also available in a 4ohm, model # ST15-4. Made in the USA.

Specifications
Frequency Response

20-120Hz +/-3dB

Sensitivity

91dB 2.83V/1m

Voltage

70V

70V Power

200W Toroidal Transformer

Woofer

(1) 15" (381mm) Aluminum

Enclosure

Aircraft Marine Grade Aluminum

Finishes

Black buried enclosure and black exposed port, custom finishes available for a nominal upcharge

Width

16.25 in (412.75 mm)

Depth

22.5 in (571.50 mm)

Height

16.25 in (412.75 mm)

Product Documents

Related Documents

Click photo for download image options

Web 151st70 side

ST15-70 - Available downloads

Title: 151ST70

Web 151st70 side
Size Resolution (Right-click: Save link as...)
206.40 KB 900x900 Web_151ST70_side.jpg
At sub install art

ST15-70 - Available downloads

Title: ST series installation

At sub install art
Size Resolution (Right-click: Save link as...)
435.31 KB 1224x900 AT-sub-install-art.jpg
70v test equipment 2

ST15-70 - Available downloads

Title: 70V testing options

70v test equipment 2
Size Resolution (Right-click: Save link as...)
116.69 KB 960x720 70V_test_equipment_2.jpg
Maxresdefault

James Loudspeaker Helps Expand Maverick Integration's Outdoor Audio Business

Dennis Jaques of Maverick Integration in Nashua, N.H., explains how the 70V Landscape Series line of speakers from James Loudspeaker enabled the company to expand its outdoor audio business.


Category FAQs
Answer:

Traditional 70V speakers will have a transformer as the load.  Because tranformers react differently to DC and AC signals, an ohm meter reading will measure the DC resistance (DCR) of the transformer and will not provide any info on the actual rating of the speaker when passing audio, and might even read near 4 or 8 ohms which might indicate incorrectly, it is a 4 or 8 ohm speaker.  In the audio band, the impedance presented by the transformer will be much greater than the DC resistance.

Unlike traditional 70V speakers, James Landscape sats, the AT series, also feature an additional low frequency roll off via a built-in network to protect the speaker as well as allow running the sats on the same line as a subwoofer.  These features block all DC signals, making an ohm-meter useless for testing as it will measure "open circuit" on both 4 ohm and 70V speakers.

So the speaker must be measured with an 70V IMPEDANCE METER which characterises the IMPEDANCE at 1kHz, not at DC RESISTANCE.  Examples follow the table.

Below is a table which shows impedance and DCR reading to be expected on AT sats and ST subwoofers.

Table1 - AT and ST loudspeaker impedance data
MODEL 1kHz DCR NOTES
32AT4 9 ohms open  
32AT70 300 ohms open  
42AT4 7 ohms open  
42AT70 150 ohms open  
62AT4 11 ohms open  
62AT70 105 ohms open  
81ST4     Bi-amp only
81ST70     Bi-amp only
81ST70-X     Crossover for fullrange systems
101ST4     Bi-amp only
101ST70     Bi-amp only
101ST70-X     Crossover for fullrange systems
121ST4     Bi-amp only
121ST70     Bi-amp only
121ST70-X     Crossover for fullrange systems
151ST4     Bi-amp only
151ST70    

Bi-amp only

Fig 1 shows three examples of 70V impedance measurement tools; the TOA  ZM-104A, the TENMA 72-6948, and the Dayton Audio DATS2 speaker testing software.  The two impedance meters test at only 1kHz which can give you readings which may appear out of spec, where as DATS2 gives you a full 20Hz to 20kHz impedance curve so you see all the data and read the frequency of interest.  DATS2 is our favorite as it works with a laptop, is small and also the cheapest of the options.

Fig 1 - 70V mesurement tools

To show the versatility of DATS2, Fig 2 below shows a DATS2 curve run on a 32AT70 loudspeaker.  To get the same reading as an impedance meter, you would read the impedance at 1kHz o the graph, but as you can see, there is a wealth of information in the curve.  In this example, DATS2 is calling out about 281 ohms at 1 kHz, close to the 300 the impedance meters will read.

For those with an understanding of the math, the power at 1kHz will be 5000/281 = 18W.  The lowest impedance is around 450 Hz at about 190 ohms, giving 5000/190 = 26W.  So as you can see, even though the transformer is rated at 30W at 4 ohms, when used with a speaker the real power is quite different. 

When this same transformer is loaded with a 4 ohm resisitive load, the reading is 140 ohms which is 5000/140 =3 5W, typical for a 30W rating.  So all contant voltage transformers, regardless if they are 25V, 70V or 100V, only have a nomial power rating at a nominal load impedance - results will vary in use!

 

Fig 2 - DATS2 curve of 32AT70

Welcome! Admin Login
Ph: +1.775.461.7500 | Fx: +1.775.461.7599
© Copyright 2022 James Loudspeaker LLC